How To Install A Honeywell Home Thermostat

T3 Pro Thermostat

Installation Instructions

Bundle Includes:

• T3 Pro Thermostat
• UWP™ Mounting Organisation
• Decorative Encompass Plate –
  Small; Size iv.72" H X 5.9" W
  (120 mm H Ten 150 mm W)
• Screws and Anchors
• 2 AA Batteries
• Thermostat Literature

Optional Embrace Plate installation

NOTE: If Optional Comprehend Plate is not required, meet "UWP Mounting Arrangement installation" on next page.
Apply the Optional Cover Plate when you need to cover paint gaps from the old thermostat.

1.  Before starting, turn the ability off at the breaker box or switch.
2. Mountain the Cover Plate to the wall using any of the 6 screw holes. Insert and tighten the mounting screws supplied with the Cover Plate. Do not overtighten. See Figure 1. Brand certain the Comprehend Plate is level.
3. Adhere the UWP by hanging information technology on the meridian claw of the Cover Plate so snapping the bottom of the
   UWP in place. Run across Figure two.
4. If mounting to a wall with no existing wall anchors:
   a. Position the Cover Plate on wall. Level and mark pigsty positions. See Figure 1.
   b. Drill holes at marked positions, and so lightly tap supplied wall anchors into the wall using a hammer.
   • If your box contains red anchors, drill seven/32" (5.6 mm) holes.
   • If your box contains yellowish anchors, drill three/16" (4.8 mm) holes.
   • Apply 2x supplied screws (#8 1-1/2" (38 mm) for cherry-red anchors and #half-dozen ane-one/2" (38 mm) for xanthous anchors).

UWP Mounting Arrangement installation

1.  Before starting, turn the power off at the breaker box or switch. Open package to find the UWP. See Figure i.
2. Position the UWP on wall. Level and mark hole positions. See Figure two.
   Drill holes at marked positions, and and then lightly tap supplied wall anchors into the wall using a hammer.
   ‒ If your box contains crimson anchors, drill vii/32" (v.six mm) holes.
   ‒ If your box contains yellow anchors, drill 3/16" (iv.viii mm) holes.
3. Pull the door open up and insert the wires through wiring hole of the UWP. See Figure 3.
4. Place the UWP over the wall anchors.
   Insert and tighten mounting screws supplied with the UWP. Do non overtighten. Tighten until the UWP no longer moves. Close the door. Run into Figure iv.

Notation: If Optional Cover Plate is required, encounter "Optional Comprehend Plate installation" on previous page.

Power options

Setting Slider Tabs (built-in jumper)

UWP Wiring final designations

* Terminal can be jumped using Slider Tab. See "Setting Slider Tabs" above.

Wiring conventional systems: forced air and hydronics

Thermostat mounting

1. Button backlog wire back into the wall opening.
2. Shut the UWP door. It should remain airtight without bulging.
3. Align the UWP with the thermostat, and push gently until the thermostat snaps in place.
4. Turn the power on at the billow box or switch.

System operation settings

i. Printing Carte du jour, and and so press the Style (+) button to cycle to the next available System mode.
2. Bicycle through the modes until the required System mode is displayed, and then press Done.

Notation: Available System modes vary past model and organisation settings.

System modes:
‒ Motorcar: Thermostat selects heating or cooling every bit needed.
‒ Heat: Thermostat controls only the heating arrangement.
‒ Absurd: Thermostat controls only the cooling organisation.
‒ Em rut (TH3210U only): For heat pumps with auxiliary heat. Thermostat controls auxiliary oestrus. Compressor is non used.
‒ Off: Heating and cooling organization is off. Fan volition still operate if fan is gear up to On.

NOTE: Heat On/Absurd On may flash for v minutes due to compressor protection.

Fan operation settings
1. Press Carte, and so press the Fan (-) button to bike to the next available Fan mode.
2. Cycle through the modes until the required Fan mode is displayed, and so press Done.
Annotation: Available Fan modes vary with arrangement settings.

Fan modes:
‒ Auto: Fan runs only when the heating or cooling organisation is on.
‒ On: Fan is always on.

Installer setup (ISU)

NOTE: The thermostat enters installer setup the first fourth dimension information technology is powered up during installation. To re-enter the Organisation Setup from the Home Screen, printing and hold the Menu button for approximately 5 seconds.

1. Select System Setup options.
   Press Edit (-) to change values or select from available options. Then printing Next (+) to save changes and advance to the next Organization Setup number.
   See "System Setup options" on the next page for a full list of System Setup numbers and options.
   Repeat until all of the System Setup options have been fix, and then printing Done. The thermostat will save and exit to the dwelling house screen.
2. Continue to "Installer setup (ISU)" on folio 6.

Installer setup (ISU)

Installer setup (ISU) (continued)

NOTE: Once you lot have cycled through all of the System Setup numbers, printing Done to save and exit to the abode screen.

Setup Complete

You take now finished installing and setting up your thermostat.

Caution: Electric Gamble
Can crusade electrical shock or equipment damage. Disconnect power before beginning installation.

CAUTION: EQUIPMENT DAMAGE Take a chance
Compressor protection is bypassed during testing. To preclude equipment damage, avert cycling the compressor quickly.

CAUTION: MERCURY NOTICE
If this production is replacing a command that contains mercury in a sealed tube, do non identify the old control in the trash. Contact your local waste material management authority for instructions regarding recycling and proper disposal.

CAUTION: ELECTRONIC Waste matter NOTICE
The product should not be disposed of with other household waste. Bank check for the nearest authorized collection centers or authorized recyclers. The right disposal of cease-of-life equipment volition assist prevent negative consequences for the environment and human health

https://customer.resideo.com/en-U.s./support/residential/codes-and-standards/FCC15105/Pages/default.aspx

Customer assistance

For assistance with this product, please visit client.resideo.com.
Or telephone call Customer Care toll-free at
1-800-468-1502.

Documents / Resources

Source: https://manuals.plus/honeywell-home/t3-pro-thermostat-manual

Posted by: phillipsmaideared.blogspot.com

Share this post